Difference between revisions of "Exhaust Module"
Line 63: | Line 63: | ||
*The Offset Wizard window will open and prompt you to choose an offset with '''3''' or '''4''' bends. | *The Offset Wizard window will open and prompt you to choose an offset with '''3''' or '''4''' bends. | ||
+ | |||
+ | |||
+ | |||
====Enter the location of the offset:==== | ====Enter the location of the offset:==== | ||
*Type in the location of the offset in the "'''Distance to Center'''" value field. Select whether the distance will be from the start or end of the selected part. | *Type in the location of the offset in the "'''Distance to Center'''" value field. Select whether the distance will be from the start or end of the selected part. | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
====Enter the size of the offset:==== | ====Enter the size of the offset:==== | ||
Line 73: | Line 82: | ||
*Type in the size of the vertical offset in the "'''Vertical Offset:'''" value field. | *Type in the size of the vertical offset in the "'''Vertical Offset:'''" value field. | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
====Enter the size/location of the offset:==== | ====Enter the size/location of the offset:==== | ||
Line 79: | Line 95: | ||
*Type in the distance from the start of the section to the ending (tangent) of the last bend in the "'''Distance to End'''" value field. | *Type in the distance from the start of the section to the ending (tangent) of the last bend in the "'''Distance to End'''" value field. | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
====Enter the length of the offset:==== | ====Enter the length of the offset:==== | ||
Line 85: | Line 109: | ||
*Type in the length of the offset in the "'''Length:'''" value field. | *Type in the length of the offset in the "'''Length:'''" value field. | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
====Select the die for each bend:==== | ====Select the die for each bend:==== | ||
Line 93: | Line 125: | ||
*Select the "'''Back''''" [[File:Exhaust_back1.png]] or "'''Next'''" [[File:Exhaust_next1.png]] buttons to navigate between the windows within the Offset Wizard. | *Select the "'''Back''''" [[File:Exhaust_back1.png]] or "'''Next'''" [[File:Exhaust_next1.png]] buttons to navigate between the windows within the Offset Wizard. | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
==Part Definition== | ==Part Definition== |
Revision as of 15:56, 3 October 2014
"UNDER CONSTRUCTION: THANK YOU FOR YOUR PATIENCE"
Bend-Tech 7x Wiki :: Exhaust Designer
- The Bend-Tech Exhaust Designer is a stand alone product which can also be an add-on module to owners of Bend-Tech 7x PRO and SE. It assists users in the design and manufacturing of exhaust pipe and tubing. New features include tabs to create mufflers, axles, cubes and cylinders to help create a mock up setting where users can design the exhaust pipes they need.
- This interface does NOT use PickPonts, but offers a 3D space with a grid to design on.
Selection
To create a Exhaust Design Part:
1.) Click the New Tube icon and select the Exhaust option in the Create New menu.
...OR
2.) Select the Exhaust option from the Task Menu that appears when the software starts up, when all designs are closed, or through the view menu.
Grid
Grid
Spacing:
- Type in a value between 1 and 50 to adjust how small or large the grid increments are in the display area.
Offset:
- Type in a positive or negative number in the value field to raise or lower the offset from the grid plane in the display area.
Width:
- Type in the value field to increase or decrease the width of the grid.
Length:
- Type in the value field to increase or decrease the length of the grid.
Set Base
- Select the "Set Base"
button to assign where the center of the grid will be placed. (Note) This can only be done after a part has been designed in the display area.
Pipe / Tubing Path
New Section
- Select the "New Section"
button to place a length of pipe along the grid in the display area using the two-click method.
Delete
Offset
- (See the Offset Part guide for more information on this topic.)
Choose the style of the offset:
- The Offset Wizard window will open and prompt you to choose an offset with 3 or 4 bends.
Enter the location of the offset:
- Type in the location of the offset in the "Distance to Center" value field. Select whether the distance will be from the start or end of the selected part.
Enter the size of the offset:
- Type in the size of the horizontal offset in the "Horizontal Offset:" value field.
- Type in the size of the vertical offset in the "Vertical Offset:" value field.
Enter the size/location of the offset:
- Type in the distance from the start of the selected section to the beginning (tangent) of the first bend in the "Distance to Start" value field.
- Type in the distance from the start of the section to the ending (tangent) of the last bend in the "Distance to End" value field.
Enter the length of the offset:
- (For use with 4 bends only)
- Type in the length of the offset in the "Length:" value field.
Select the die for each bend:
- Select the dies for each of the 3 or 4 bends that are to be created by picking them from their drop down menus.
- Select the "Cancel"
button to cancel the offset or select the "OK"
button to continue with the creation of the offset.
Part Definition
Define
- Select the "Define"
button to determine the order in which parts in the display area are to be connected. Select each section (in order) to create a part out of multiple straight parts.
Delete
Objects / Obstacles
![Exhaust objectsobstacles1.png](/wiki7/images/7/7a/Exhaust_objectsobstacles1.png)
Muffler
- The "Add Muffler" window will open. The box to the right is reserved for previously saved muffler templates created by the user.
Enter the overall size of the muffler:
- Type in the height of the muffler body in the "Height:" value field.
- Type in the width of the muffler body in the "Width:" value field.
- Type in the length of the muffler body in the "Length:" value field.
- Select the "Muffler Color:" button to change the color of the part when it appears in the display area.
Enter the location of the inlet tube:
"For these steps, assume you're looking at the "front" face-plate of the muffler body"
- Type in the horizontal distance from the far right side of the body to place the horizontal location of the inlet exhaust pipe.
- Type in the vertical distance from the bottom of the body to place the vertical location of the inlet pipe.
- Type in the diameter of the pipe itself.
Enter the location of the outlet tube(s):
"For these steps, assume you're looking at the "back" face-plate of the muffler body"
- Type in the horizontal distance from the far right side of the body to place the horizontal location of the outlet tailpipe.
- Type in the vertical distance from the bottom of the body to place the vertical location of the outlet tailpipe.
- Type in the diameter of the pipe itself.
You can duplicate these steps and create an additional outlet by selecting the "Second Outlet" check box.