Motor Sports Templates II

...Motor Sports Templates Continued.

For initial information on MSP Templates, see Motor Sport Templates.

Mounts Category

• The fourth button in the "Style of Plate" section is for Shackles, Mounts, and Plates style projects.

Spare Tire Mount

Current Template Values:

• The distance labeled "L1" (default 1) is the length from the center of the middle hole to the center of the stud holes.
• The distance labeled "D1" (default 5) is the length of the diameter of the outside edge of the part.
• The distance labeled "D2" (default 3) is the length of the diameter of the center hole.
• The distance labeled "D3" (default .5) is the length of the diameter of the stud holes.
• The pink "#" is the number of stud holes the user would like to create circling the part.

Tube Tab

Current Template Values:

• The distance labeled "L1" (default 5) is the length from the center of the top hole to the center of the bottom hole.
• The distance labeled "R1" (default 1) is the length from the center of the top hole to the top arc.
• The distance labeled "R2" (default 2) is the length from the center of the bottom hole to the bottom arc.
• The distance labeled "D1" (default 5) is the length of the diameter of the top hole.
• The distance labeled "D2" (default 3) is the length of the diameter of the bottom hole.

Bolt Lock

Current Template Values:

• The distance labeled "L1" (default 3) is the length from the center of the top hole to the center of the bottom hole.
• The distance labeled "L2" (default .75) is the length of the diameter of the inner edge of the top hole.
• The distance labeled "R1" (default 1) is the length from the center of the top hole to the top arc.
• The distance labeled "R2" (default .5) is the length from the center of the bottom hole to the bottom arc.
• The distance labeled "D1" (default .25) is the length of the diameter of the bottom hole.

Shackle 2 Hole

Current Template Values:

• The distance labeled "L1" (default 5) is the length from the center of the top hole to the center of the bottom hole.
• The distance labeled "R1" (default 1) is the length from the center of the top hole to the top arc, or from the center of the bottom hole to the bottom arc.
• The distance labeled "D1" (default .5) is the length of the diameter either the top or bottom hole.

Shackle 3 Hole

Current Template Values:

• The distance labeled "L1" (default 5) is the length from the center of the top hole to the center of the bottom hole.
• The distance labeled "L2" (default 2.5) is the length from the center of the middle hole to the center of the bottom hole.
• The distance labeled "R1" (default 1) is the length from the center of the top hole to the top arc, or from the center of the bottom hole to the bottom arc.
• The distance labeled "D1" (default .5) is the length of the diameter either the top or bottom hole.
• The distance labeled "D2" (default 1) is the length of the diameter of the middle hole.

Shackle 2 Hole - Offset

Current Template Values:

• The distance labeled "L1" (default 5) is the length from the center of the top hole to the center of the bottom hole.
• The distance labeled "L2" (default 1) is the width of the part as a whole.
• The distance labeled "L3" (default 2) is the length from the bottom of the part to the lowest bend.
• L4
• The distance labeled "D1" (default .5) is the length of the diameter of either the top or bottom hole.

Shackle 3 Hole - Offset

Current Template Values:

• The distance labeled "L1" (default 5) is the length from the center of the top hole to the center of the bottom hole.
• The distance labeled "L2" (default 1) is the width of the part as a whole.
• The distance labeled "L3" (default 1.5) is the length for the center of the top hole to the center of the middle hole.
• The distance labeled "L4" (default 2) is the length from the bottom of the part to the lowest bend.
• L5
• The distance labeled "D1" (default .25) is the length of the diameter of either the top or bottom hole.
• The distance labeled "D2" (default .5) is the length of the diameter of the middle hole.

Oval Mount

Current Template Values:

• The distance labeled "L1" (default ) is the length from the center of the top hole to the center of the middle hole.
• The distance labeled "R1" (default ) is the length from the center of the top hole to the top arc, or from the center of the bottom hole to the bottom arc.
• The distance labeled "R2" (default ) is the length from the center of the middle hole to the left and right arcs.
• The distance labeled "D1" (default ) is the length of the diameter of the middle hole.
• The distance labeled "D2" (default ) is the length of the diameter of either the top or bottom hole.

Through Plate

Current Template Values:

• The distance labeled "L1" (default 2) is the horizontal and vertical length from the center of the middle hole to the center of any other hole.
• The distance labeled "R1" (default 1) is the length from the center of any outer hole to its arc.
• The distance labeled "D1" (default 1) is the length of the diameter of the middle hole.
• The distance labeled "D2" (default .25) is the length of the diameter of any outer holes.

Square Mount

Current Template Values:

• The distance labeled "L1" (default 2) is the horizontal and vertical length from the center of the middle hole to the center of any other hole.
• The distance labeled "R1" (default 1) is the length from the center of any outer hole to its arc.
• The distance labeled "D1" (default 1) is the length of the diameter of the middle hole.
• The distance labeled "D2" (default .25) is the length of the diameter of any outer holes.

Gusset Category

• The fifth button in the "Style of Plate" section is for Gussets style projects.

Gusset

Current Template Values:

• The value labeled "A1" (default 90) is the angle of the outside of the part.
• The value labeled "A2" (default 120) is the angle of the inside of the part.
• The distance labeled "L1" (default 4) is the width of the part from end to end.
• The distance labeled "R1" (default 1) is the length from the center of the part to the outer arc.
• The distance labeled "R2" (default .25) is the size of the leg's outer arcs.

Gusset Cutout