Difference between revisions of "Motor Sports Templates II"
| Line 166: | Line 166: | ||
*The distance labeled "'''R2'''" (default .5) is the size of the outer arc. | *The distance labeled "'''R2'''" (default .5) is the size of the outer arc. | ||
| − | ==Suspension/Traction Bar Mounts [[File:susp_trac.png]]== | + | ==Suspension/Traction Bar Mounts Category [[File:susp_trac.png]]== |
*The sixth button in the "'''Style of Plate'''" section is for "'''Suspension Mounts and Traction Bar Mounts'''" style projects. | *The sixth button in the "'''Style of Plate'''" section is for "'''Suspension Mounts and Traction Bar Mounts'''" style projects. | ||
| + | |||
| + | ==Buggy Link (lower)== | ||
| + | [[File:msp_temp38.png|right]] | ||
| + | ====Current Template Values:==== | ||
| + | *The distance labeled "'''L1'''" (default 3) is the width of the part from end to end. | ||
| + | *The distance labeled "'''L2'''" (default 4) is the height of the part. | ||
| + | *The distance labeled "'''L3'''" (default 1.5) is the length from the top to the bottom of the "'''R2'''" arcs in the top hole. | ||
| + | *The distance labeled "'''L4'''" (default .5) is the length from the bottom edge of the part to the center of the "'''D1'''" holes. | ||
| + | *The distance labeled "'''L5'''" (default 1) is the length from the center of one "'''D1'''" hole to another. | ||
| + | *The distance labeled "'''R1'''" (default 1) is the size of the top outer arc. | ||
| + | *The distance labeled "'''R2'''" (default .5) is the size of the top hole's inner arc. | ||
| + | *The distance labeled "'''R3'''" (default .25) is the size of the bottoms corner's arcs. | ||
| + | *The distance labeled "'''D1'''" (default .5) is the length of the diameter of each of the bottom holes. | ||
| + | |||
| + | ==Buggy Link (upper)== | ||
| + | [[File:msp_temp39.png|right]] | ||
| + | ====Current Template Values:==== | ||
| + | *The distance labeled "'''L1'''" (default 4) is the width of the part from end to end. | ||
| + | *The distance labeled "'''L2'''" (default 4) is the height of the part. | ||
| + | *The distance labeled "'''L3'''" (default 1.5) is the length from the top to the bottom of the "'''R2'''" arcs in the top hole. | ||
| + | *The distance labeled "'''L4'''" (default .5) is the length from the bottom edge of the part to the center of the "'''D1'''" holes. | ||
| + | *The distance labeled "'''L5'''" (default 1) is the length from the center of one "'''D1'''" hole to another. | ||
| + | *The distance labeled "'''R1'''" (default 1) is the size of the top outer arc. | ||
| + | *The distance labeled "'''R2'''" (default .5) is the size of the top hole's inner arc. | ||
| + | *The distance labeled "'''R3'''" (default .375) is the size of the bottoms corner's arcs. | ||
| + | *The distance labeled "'''D1'''" (default .25) is the length of the diameter of each of the bottom holes. | ||
| + | |||
| + | "'''New Motor Sports Templates will be updated periodically. Thank you.'''" | ||
Revision as of 10:44, 26 November 2014
...Motor Sports Templates Continued.
For initial information on MSP Templates, see Motor Sport Templates.
Contents
- 1 Mounts Category
- 2 Gusset Category
Mounts Category 
- The fourth button in the "Style of Plate" section is for Shackles, Mounts, and Plates style projects.
Spare Tire Mount
Current Template Values:
- The distance labeled "L1" (default 1) is the length from the center of the middle hole to the center of the stud holes.
- The distance labeled "D1" (default 5) is the length of the diameter of the outside edge of the part.
- The distance labeled "D2" (default 3) is the length of the diameter of the center hole.
- The distance labeled "D3" (default .5) is the length of the diameter of the stud holes.
- The pink "#" is the number of stud holes the user would like to create circling the part.
Tube Tab
Current Template Values:
- The distance labeled "L1" (default 5) is the length from the center of the top hole to the center of the bottom hole.
- The distance labeled "R1" (default 1) is the length from the center of the top hole to the top arc.
- The distance labeled "R2" (default 2) is the length from the center of the bottom hole to the bottom arc.
- The distance labeled "D1" (default 5) is the length of the diameter of the top hole.
- The distance labeled "D2" (default 3) is the length of the diameter of the bottom hole.
Bolt Lock
Current Template Values:
- The distance labeled "L1" (default 3) is the length from the center of the top hole to the center of the bottom hole.
- The distance labeled "L2" (default .75) is the length of the diameter of the inner edge of the top hole.
- The distance labeled "R1" (default 1) is the length from the center of the top hole to the top arc.
- The distance labeled "R2" (default .5) is the length from the center of the bottom hole to the bottom arc.
- The distance labeled "D1" (default .25) is the length of the diameter of the bottom hole.
Shackle 2 Hole
Current Template Values:
- The distance labeled "L1" (default 5) is the length from the center of the top hole to the center of the bottom hole.
- The distance labeled "R1" (default 1) is the length from the center of the top hole to the top arc, or from the center of the bottom hole to the bottom arc.
- The distance labeled "D1" (default .5) is the length of the diameter either the top or bottom hole.
Shackle 3 Hole
Current Template Values:
- The distance labeled "L1" (default 5) is the length from the center of the top hole to the center of the bottom hole.
- The distance labeled "L2" (default 2.5) is the length from the center of the middle hole to the center of the bottom hole.
- The distance labeled "R1" (default 1) is the length from the center of the top hole to the top arc, or from the center of the bottom hole to the bottom arc.
- The distance labeled "D1" (default .5) is the length of the diameter either the top or bottom hole.
- The distance labeled "D2" (default 1) is the length of the diameter of the middle hole.
Shackle 2 Hole - Offset
Current Template Values:
- The distance labeled "L1" (default 5) is the length from the center of the top hole to the center of the bottom hole.
- The distance labeled "L2" (default 1) is the width of the part as a whole.
- The distance labeled "L3" (default 2) is the length from the bottom of the part to the lowest bend.
- L4
- The distance labeled "D1" (default .5) is the length of the diameter of either the top or bottom hole.
Shackle 3 Hole - Offset
Current Template Values:
- The distance labeled "L1" (default 5) is the length from the center of the top hole to the center of the bottom hole.
- The distance labeled "L2" (default 1) is the width of the part as a whole.
- The distance labeled "L3" (default 1.5) is the length for the center of the top hole to the center of the middle hole.
- The distance labeled "L4" (default 2) is the length from the bottom of the part to the lowest bend.
- L5
- The distance labeled "D1" (default .25) is the length of the diameter of either the top or bottom hole.
- The distance labeled "D2" (default .5) is the length of the diameter of the middle hole.
Oval Mount
Current Template Values:
- The distance labeled "L1" (default ) is the length from the center of the top hole to the center of the middle hole.
- The distance labeled "R1" (default ) is the length from the center of the top hole to the top arc, or from the center of the bottom hole to the bottom arc.
- The distance labeled "R2" (default ) is the length from the center of the middle hole to the left and right arcs.
- The distance labeled "D1" (default ) is the length of the diameter of the middle hole.
- The distance labeled "D2" (default ) is the length of the diameter of either the top or bottom hole.
Through Plate
Current Template Values:
- The distance labeled "L1" (default 2) is the horizontal and vertical length from the center of the middle hole to the center of any other hole.
- The distance labeled "R1" (default 1) is the length from the center of any outer hole to its arc.
- The distance labeled "D1" (default 1) is the length of the diameter of the middle hole.
- The distance labeled "D2" (default .25) is the length of the diameter of any outer holes.
Square Mount
Current Template Values:
- The distance labeled "L1" (default 2) is the horizontal and vertical length from the center of the middle hole to the center of any other hole.
- The distance labeled "R1" (default 1) is the length from the center of any outer hole to its arc.
- The distance labeled "D1" (default 1) is the length of the diameter of the middle hole.
- The distance labeled "D2" (default .25) is the length of the diameter of any outer holes.
Gusset Category 
- The fifth button in the "Style of Plate" section is for Gussets style projects.
Gusset
Current Template Values:
- The value labeled "A1" (default 90) is the angle of the outside of the part.
- The value labeled "A2" (default 120) is the angle of the inside of the part.
- The distance labeled "L1" (default 4) is the width of the part from end to end.
- The distance labeled "R1" (default 1) is the length from the center of the part to the outer arc.
- The distance labeled "R2" (default .25) is the size of the leg's outer arcs.
Gusset Cutout
Current Template Values:
- The value labeled "A1" (default 90) is the angle of the outside of the part.
- The distance labeled "L1" (default 4) is the width of the part from end to end.
- The distance labeled "L2" (default .5) is the width of the section from either the bottom edge to the inner edge, or the right edge to the inner edge.
- The distance labeled "L3" (default .5) is the width of the section from the diagonal outer edge to the inner edge.
- The distance labeled "R1" (default 1) is the length from the inner section of the part to the outer arc.
- The distance labeled "R2" (default .25) is the size of the leg's outer arcs.
- The distance labeled "R3" (default .1) is the size of the leg's inner arcs.
Gusset 1 Hole
Current Template Values:
- The value labeled "A1" (default 90) is the angle of the outside of the part.
- The distance labeled "L1" (default 4) is the height of the part from top to bottom.
- The distance labeled "L2" (default 1) is the length from the center of the part to the inner arc.
- The distance labeled "R1" (default 1) is the length from the center of the part to the outer arc.
- The distance labeled "R2" (default .25) is the size of the leg's outer arcs.
- The distance labeled "R3" (default 4) is the size of the inner arc.
- The distance labeled "D1" (default 1) is the length of the diameter of the middle hole.
Gusset 2 Hole
Current Template Values:
- The value labeled "A1" (default 90) is the angle of the outside of the part.
- The distance labeled "L1" (default 4) is the width of the part from end to end.
- The distance labeled "L2" (default .5) is the width of the section from either the bottom edge to the center of the bottom hole, or the right edge to the center of the right hole.
- The distance labeled "L3" (default 1.5) is the length from one hole's center to the other.
- The distance labeled "R1" (default 1) is the length from the inner section of the part to the outer arc.
- The distance labeled "R2" (default .25) is the size of the leg's outer arcs.
- The distance labeled "R3" (default 4) is the size of the inner arc.
- The distance labeled "D1" (default 1) is the length of the diameter of either hole.
Gusset 5 Hole
Current Template Values:
- The value labeled "A1" (default 90) is the angle of the outside of the part.
- The value labeled "A2" (default 120) is the angle of the inside of the part.
- The distance labeled "L1" (default 4) is the height of the part from top to bottom.
- The distance labeled "L2" (default .5) is the length of the section on the outer edge where the legs meet.
- The distance labeled "L3" (default .25) is the length from any outer edge to the closest edge of any hole.
- The distance labeled "L4" (default .75) is the length from the center of the "D1" hole to the center of either "D2" holes.
- The distance labeled "L5" (default 1) is the length from the center of either "D3" hole to the edge of the closest leg's arc
- The distance labeled "R1" (default .25) is the size of the leg's outer arcs.
- The distance labeled "D1" (default .75) is the length of the diameter of the middle hole.
- The distance labeled "D2" (default .5) is the length of the diameter of the inner most holes.
- The distance labeled "D3" (default .25) is the length of the diameter of the outer most holes.
Gusset Webbed
Current Template Values:
- The value labeled "A1" (default 90) is the angle of the outside of the part.
- The distance labeled "L1" (default 4) is the height of the part from top to bottom.
- The distance labeled "L2" (default 3) is the length from the outer arc "R2" to where the inner arcs "R1" meet.
- The distance labeled "R1" (default 3) is the size of the two inner arcs.
- The distance labeled "R2" (default .5) is the size of the outer arc.
Suspension/Traction Bar Mounts Category 
- The sixth button in the "Style of Plate" section is for "Suspension Mounts and Traction Bar Mounts" style projects.
Buggy Link (lower)
Current Template Values:
- The distance labeled "L1" (default 3) is the width of the part from end to end.
- The distance labeled "L2" (default 4) is the height of the part.
- The distance labeled "L3" (default 1.5) is the length from the top to the bottom of the "R2" arcs in the top hole.
- The distance labeled "L4" (default .5) is the length from the bottom edge of the part to the center of the "D1" holes.
- The distance labeled "L5" (default 1) is the length from the center of one "D1" hole to another.
- The distance labeled "R1" (default 1) is the size of the top outer arc.
- The distance labeled "R2" (default .5) is the size of the top hole's inner arc.
- The distance labeled "R3" (default .25) is the size of the bottoms corner's arcs.
- The distance labeled "D1" (default .5) is the length of the diameter of each of the bottom holes.
Buggy Link (upper)
Current Template Values:
- The distance labeled "L1" (default 4) is the width of the part from end to end.
- The distance labeled "L2" (default 4) is the height of the part.
- The distance labeled "L3" (default 1.5) is the length from the top to the bottom of the "R2" arcs in the top hole.
- The distance labeled "L4" (default .5) is the length from the bottom edge of the part to the center of the "D1" holes.
- The distance labeled "L5" (default 1) is the length from the center of one "D1" hole to another.
- The distance labeled "R1" (default 1) is the size of the top outer arc.
- The distance labeled "R2" (default .5) is the size of the top hole's inner arc.
- The distance labeled "R3" (default .375) is the size of the bottoms corner's arcs.
- The distance labeled "D1" (default .25) is the length of the diameter of each of the bottom holes.
"New Motor Sports Templates will be updated periodically. Thank you."
