Motor Sports Templates II

From Bend-Tech 7x Wiki
Revision as of 15:54, 25 November 2014 by Fabcam1 (talk | contribs)
Jump to: navigation, search

...Motor Sports Templates Continued.

For initial information on MSP Templates, see Motor Sport Templates.

Mounts Category Msp mounts.png

  • The fourth button in the "Style of Plate" section is for Shackles, Mounts, and Plates style projects.

Spare Tire Mount

Msp temp22.png

Current Template Values:

  • The distance labeled "L1" (default 1) is the length from the center of the middle hole to the center of the stud holes.
  • The distance labeled "D1" (default 5) is the length of the diameter of the outside edge of the part.
  • The distance labeled "D2" (default 3) is the length of the diameter of the center hole.
  • The distance labeled "D3" (default .5) is the length of the diameter of the stud holes.
  • The pink "#" is the number of stud holes the user would like to create circling the part.

Tube Tab

Msp temp23.png

Current Template Values:

  • The distance labeled "L1" (default 5) is the length from the center of the top hole to the center of the bottom hole.
  • The distance labeled "R1" (default 1) is the length from the center of the top hole to the top arc.
  • The distance labeled "R2" (default 2) is the length from the center of the bottom hole to the bottom arc.
  • The distance labeled "D1" (default 5) is the length of the diameter of the top hole.
  • The distance labeled "D2" (default 3) is the length of the diameter of the bottom hole.

Bolt Lock

Msp temp24.png

Current Template Values:

  • The distance labeled "L1" (default 3) is the length from the center of the top hole to the center of the bottom hole.
  • The distance labeled "L2" (default .75) is the length of the diameter of the inner edge of the top hole.
  • The distance labeled "R1" (default 1) is the length from the center of the top hole to the top arc.
  • The distance labeled "R2" (default .5) is the length from the center of the bottom hole to the bottom arc.
  • The distance labeled "D1" (default .25) is the length of the diameter of the bottom hole.

Shackle 2 Hole

Msp temp25.png

Current Template Values:

  • The distance labeled "L1" (default 5) is the length from the center of the top hole to the center of the bottom hole.
  • The distance labeled "R1" (default 1) is the length from the center of the top hole to the top arc, or from the center of the bottom hole to the bottom arc.
  • The distance labeled "D1" (default .5) is the length of the diameter either the top or bottom hole.

Shackle 3 Hole

Msp temp26.png

Current Template Values:

  • The distance labeled "L1" (default 5) is the length from the center of the top hole to the center of the bottom hole.
  • The distance labeled "L2" (default 2.5) is the length from the center of the middle hole to the center of the bottom hole.
  • The distance labeled "R1" (default 1) is the length from the center of the top hole to the top arc, or from the center of the bottom hole to the bottom arc.
  • The distance labeled "D1" (default .5) is the length of the diameter either the top or bottom hole.
  • The distance labeled "D2" (default 1) is the length of the diameter of the middle hole.

Shackle 2 Hole - Offset

Msp temp27.png

Current Template Values:

  • The distance labeled "L1" (default 5) is the length from the center of the top hole to the center of the bottom hole.
  • The distance labeled "L2" (default 1) is the width of the part as a whole.
  • The distance labeled "L3" (default 2) is the length from the bottom of the part to the lowest bend.
  • L4
  • The distance labeled "D1" (default .5) is the length of the diameter of either the top or bottom hole.

Shackle 3 Hole - Offset

Msp temp28.png

Current Template Values:

  • The distance labeled "L1" (default 5) is the length from the center of the top hole to the center of the bottom hole.
  • The distance labeled "L2" (default 1) is the width of the part as a whole.
  • The distance labeled "L3" (default 1.5) is the length for the center of the top hole to the center of the middle hole.
  • The distance labeled "L4" (default 2) is the length from the bottom of the part to the lowest bend.
  • L5
  • The distance labeled "D1" (default .25) is the length of the diameter of either the top or bottom hole.
  • The distance labeled "D2" (default .5) is the length of the diameter of the middle hole.

Oval Mount

Msp temp29.png

Current Template Values:

Retrieved from "http://www.bend-tech.net/wiki7/index.php?title=Motor_Sports_Templates_II&oldid=4317"